內蒙古輕鋼別墅廠家告訴您鋼結構的連接方法有焊接、普通螺栓連接、高強度螺栓連接。

1.焊接：施工單位采用的鋼尺、焊接材料、焊接方法等，應進行焊接工藝評定。焊工應經考試合格并取得資格證書，應在認可范圍內焊接作業，嚴禁無證上崗。

焊接：鋼結構焊接缺陷通常分為：裂紋、空穴、固體夾雜、未熔合、未焊透，形狀缺陷和上述以外的其他缺陷。其主要處理方法為：

產出缺陷處焊縫金屬，進行補焊。

2.普通螺栓連接制孔可采用鉆孔，沖孔，洗孔，鉸孔，等方法，對直徑較大或長形孔也可采用氣割制孔。嚴禁氣割擴孔。鉆孔，沖孔為一次制孔(其中，沖孔的板厚應≤12mm)銑孔，鉸孔等為二次制孔，即在一次制孔的基礎上進行孔的二次加工。采用氣割制孔的方法，實際加工時一般直徑在80mm以上的圓孔，鉆孔不能實現時可采用氣割制孔，另外對于長園孔或異形孔一般可以采用先行鉆孔然后采用氣割制孔的方法。

3.高強螺栓連接

高強度螺栓按連接形式通常分為摩擦連接、張拉連接和承壓連接等，其中摩擦連接時目前廣泛采用基本陜西鋼結構連接方式高強度螺栓連接處摩擦面的處理方法通常有噴砂法，酸洗法，砂輪打磨法和鋼絲刷人工除銹。可根據設計抗滑移系數的要求選擇處理工藝，抗滑移系數需滿足設計要求。

聲明：文字、圖片均來自網絡，如有侵權請聯系網站管理員刪除！